Cone crusher drive shaft parts including drive shaft frame, shaft, bearings and couplings. Crusher transmission parts require high precision assembly parts.Before installation must carefully check if the bumps, rust, rotation is not flexible, so they should open the cleaning, assembling repaired.Crusher accessories parts packed in front of the rack, should be put away at the flange old gasket in order to adjust the gear meshing clearance. Should the new gasket must be consistent with the old gasket thickness, it is easy to adjust. Drive shaft is loaded, the application of model checking and gear size. Transmission gear axial runout allows 0.4-0.8mm. For alloy bearing, top clearance of 0.27-0.45mm 0.15-0.25mm backlash. For copper pad, the top gap is 0.5-0.6mm, the side gap of 0.35-0.45mm. Shaft and bearing contact surface should be evenly grinding, the contact points 3-4 points / in ² (lin = 2.54 cm).
Motor shaft crusher drive shaft center deviation allowed greater than 0.15mm. When the deviation is too large, not only can cause the motor overload and increased bearing load, so that the running bearing heating or vibration, or even cause damage to the bearings.
(1) the base aspect centerline and installation baseline deviation of not greater than ± 3ram.
(2) base elevation deviation should not exceed 3ram.
(3) the base level to 0.05 mm / m.
(4) stand eccentric sleeve assembly shall comply with the following requirements:
1, eccentric, base bushing and the joint surface of the bottom tray should be cleaned prior to assembly.
2, adjusting pads on the bottom tray and thrust pad, the order specified by the equipment technical documentation for assembly with special tool. The assembly should be coated with enough oil.
3, the eccentric sleeve and bottom special tool fixed only after the load base bushing.
(5) with the gap between the tapered bushing, crushing cone spindle and eccentric base bushing
(6) bowl-shaped bearing base connection, according to the group marked for installation in the circumferential direction of the tangent key wedge, cooling jacket should be done 0.4MPa water pressure test.
(7) The bevel gear assembly shall meet the following requirements:
1, the gear meshing clearance shall comply with the the equipment technical documents.
2, the gear meshing contact spots along the tooth height and tooth length of not less than 40%, and should tend to the middle of the flank.
3, the outer end face of the two meshing gears should be flush.
(8) bowl bearings and the crushing cone spindle oil passage hole before assembly should be blown clean.
(9) Handling bowl bearings, slings should not be pressure on the slinger.
(10) when installing the crushing cone not to damage the cone.
(11) crushing cone with bowl-shaped bearing, shall meet the following requirements:
1, the crushing cone spherical bowl pad cylindrical contact, the contact width.
2, the contact surface of the contact points, should not be less than 2 points / 50mm × 50mm.
Related Articles
Raymond technologic line of bentonite
Bentonite is a clay mineral montmorillonite aqueous clay known as known as "universal" do binder, suspending agent, thixotropic agent, stabilizer, purification bleaching agent, filling material,...
Price for mobile stone crushers in japan
The price of mobile stone crushers in Japan varies depending on several factors such as the model, brand, and features of the machine. Generally, the...
What is a sand making machine?
Deconstructing Kinetic Cleavage Physics: What is a sand making machine? To define a sand making machine merely as a piece of equipment that produces fine...
Mining production line process flow
How does the mining production line process improve the value of the ore itself? Reasonable selection and configuration of mining crushing production line is the...
Raymond Mill for Grinding Coal Powder
Coal powder is a fine powder of coal that is used as fuel in a variety of industrial applications, including power generation, cement manufacturing, and...
Ceramic ball mill for sale in india
Ceramic ball mill introduction: The relationship of the ceramic ball mill product size and production capacity of the mill change the nature of the differences...
calcite crushing equipment in south africa
Calcite is a widely occurring mineral that is primarily composed of calcium carbonate (CaCO3). It is commonly found in sedimentary rocks and has various industrial...
Sandvik sand washing machine for sale United States
Sandvik sand wash plant is artificial sand washing equipment (including natural sand). beneficiation equipment, sand washing machine washing of materials widely used in gravel pits,...
Continuous Ball Mill Manufacturers in India
Continuous ball mills are a type of grinding mill that uses rotating balls to grind materials. They are often used in the mining, mineral processing,...
Crusher Conveyor Belt Manufacturers in Malaysia
Crusher conveyor belts are an essential part of any mining or quarrying operation. They are used to transport crushed material from the crusher to the...